Most people meet a break-even calculator the moment they are deciding whether a product is worth launching or keeping, which is also the moment they are least able to tell which of their costs belong in which box.

This page sets out exactly what this calculator computes: the break-even point formula in units and in sales, how contribution per unit is worked out, how fixed and variable costs are separated, and how rounding is applied before the result is shown. Then it runs one worked example with realistic figures so you can rerun the arithmetic yourself, and it lists the assumptions the answer rests on, including the one most tools hide, which is that price and unit cost stay the same at every level of sales.

A rate is a fact with a date. This calculation uses no outside rate. Every cost and price in it is your input, and the result is a model, not a forecast of what you will sell.

This is general information, not financial advice. It is not medical advice either. Check any figure against the source named on the page.

Here is the formula

The calculation has two steps:

Contribution per unit = price per unit − variable cost per unit

Break-even units = fixed costs ÷ contribution per unit

If you want the answer as a sales figure rather than a number of units:

Contribution margin ratio = contribution per unit ÷ price per unit

Break-even sales = fixed costs ÷ contribution margin ratio

Both routes give the same point. One counts it in units, the other in money. Contribution is the part of each sale left over after the costs that come with that sale. It is the part that pays for fixed costs, and once those are covered, it is profit.

Our markup vs margin calculator works on the same price and cost inputs and is a useful cross-check on the contribution figure.

The source for this formula

This is standard cost arithmetic. No outside rate sits inside it, so the sources that matter are the ones for your inputs: supplier invoices for variable costs, leases and contracts for fixed costs, and your own price list, each with the date you read it. The U.S. Small Business Administration’s guide to writing a business plan covers the financial section where these figures are usually set out together.

Fixed costs and variable costs

The formula only works if each cost goes in the right box.

  • Fixed costs stay the same over the period whether you sell one unit or many. Examples of the kind: rent, insurance premiums, software subscriptions, salaried wages.
  • Variable costs rise with each unit sold. Examples of the kind: materials, packaging, per-order shipping, payment processing charged per sale.

Some costs are a mix. A phone plan with a fixed monthly charge and a per-use charge has a fixed part and a variable part. Split it, and put each part in its own box.

Use the same period for every fixed cost. If rent is monthly and insurance is annual, convert both to the same period before adding them.

A simple test for any cost line: if you sold nothing at all this month, would you still pay it? If yes, it is fixed for this purpose. If it would fall to nothing, it is variable. If it would fall but not to nothing, it is a mix, and the part that remains is the fixed part.

Worked example

The figures below are example inputs chosen to make the arithmetic easy to follow. They are not typical for any business, and the arithmetic is the same in any currency.

  1. Example fixed costs for one month: 3,000.
  2. Example price per unit: 50.
  3. Example variable cost per unit: 30.
  4. Contribution per unit: 50 − 30 = 20.
  5. Break-even units: 3,000 ÷ 20 = 150 units in the month.
  6. Contribution margin ratio: 20 ÷ 50 = 0.40.
  7. Break-even sales: 3,000 ÷ 0.40 = 7,500 in the month.

Check it yourself the other way: 150 units × 50 = 7,500 in sales. 150 units × 30 = 4,500 in variable costs. 7,500 − 4,500 − 3,000 = 0. At 150 units, sales cover every cost and nothing is left over, which is what break-even means.

Now replace each example figure with your own and run the same seven lines.

Rounding

Break-even units rarely come out as a whole number. If the division gives a fraction, round up, not down. Selling part of a unit is not possible, and rounding down gives a point where the business is still slightly short of covering its costs. Keep the unrounded contribution figure in your spreadsheet and round only the final count.

This assumes

  • The price per unit stays the same at every level of sales.
  • The variable cost per unit stays the same at every level of sales.
  • Fixed costs stay the same over the period.
  • Every unit made is sold in the same period.
  • There is one product, or a mix of products that stays in the same proportions.

When the break-even point formula is wrong

The arithmetic holds. The model stops describing the business when one of its assumptions does not:

  • Price changes with volume. Discounts for larger orders lower the contribution on those units.
  • Unit costs change with volume. A supplier’s price breaks can lower variable cost; a busy period that needs overtime can raise it.
  • Fixed costs step up. Past a certain volume, more space or more staff may be needed, and the fixed cost line jumps.
  • Several products. If the mix of products changes, the average contribution changes, and so does the break-even point.
  • Contribution is zero or negative. If variable cost per unit is equal to or above price, no number of sales reaches break-even. The calculator will show an error or a negative number. The fix is in the price or the cost, not in the volume.
  • Timing. Break-even in a month says nothing about cash. Costs may be paid before sales come in.

More than one product

With several products, each has its own contribution per unit. The usual approach is a weighted average:

  1. Work out the contribution per unit for each product.
  2. Write down the share of total units each product makes up, from your own sales records.
  3. Multiply each product’s contribution by its share, and add the results. This is the weighted contribution per unit.
  4. Divide fixed costs by the weighted contribution. This is the break-even count across all products, in the same mix.

If the mix changes, the weighted contribution changes with it, so run this again whenever the shares move.

Using the result

A break-even figure is most useful as a comparison, run more than once with different inputs:

  1. Run it at your current price. Note the break-even units.
  2. Change one input at a time. Try a different price, then a different variable cost, then a different fixed cost. Note how far the break-even point moves each time.
  3. Find the input that moves it most. That is the figure worth checking hardest against your records.
  4. Compare with your own sales records. If you already sell the product, set the break-even count beside the units you sold in recent periods.
  5. Write down the date and inputs. When a cost changes, run it again.

Questions to bring to an accountant

  • Have I put each cost in the right box, fixed or variable?
  • Which costs in my records are a mix of the two?
  • Is a monthly break-even the right period for this product, or would a different period be clearer?
  • How should I treat my own pay in the fixed costs?

The related question: how many units for a target profit?

Add the profit you want to the fixed costs and divide by contribution per unit: units for target profit = (fixed costs + target profit) ÷ contribution per unit. With the example figures and an example target profit of 1,000, that is (3,000 + 1,000) ÷ 20 = 200 units. The same assumptions apply, and the same habit helps: write down your inputs and the date.

Further reading

  • U.S. Small Business Administration (sba.gov): planning and running a small business.
  • Internal Revenue Service (irs.gov): federal tax information for businesses.

This is general information, not financial advice. It is not medical advice either. Check any figure against the source named on the page.

Expert Calculators Editorial